Difference between revisions of "HV Transformer"

From Industrial-Craft-Wiki
Jump to navigation Jump to search
(Adding info for consistency between all transformer pages)
(new power system)
Line 10: Line 10:
}}
}}


Unlike Real Life™, there is no actual "voltage" in IC². EU travels in "packets" through wires with near-infinite speed and has smart pathfinding (somewhat like RP2 pneumatic tubes). Packets are measured in size (in EU/p) and volume (EU). (Size being the amount of energy it contains as it leaves a storage unit, volume being how much energy is left in each packet after inefficient cable usage).
A HV Transformer is used to limit energy flow to 512 EU/t.


A HVT (or High Voltage Transformer) operates in two different ways.
Transformers have two modes - step-up and step-down. By default, a transformer will operate in step-down mode unless it receives a redstone signal. This can be changed in the GUI.


* If redstone power is '''not''' applied, it consumes 2048 EU in '''any packet size''' and converts them into up to four 512 EU/p. '''All conversions are limited to one per tick. (Converting 2048 EU into 4x512 EU is considered one conversion.)'''
In step-down mode, an HV transformer will accept up to 2048 EU/t to the 5-dot face without exploding, and output 512 EU/t from the 1-dot faces.
* If redstone power is applied, it consumes 2048 EU in '''any packet size''' and converts them into one 2048 EU/p. '''All conversions are limited to one per tick.'''
Step-up mode appears to be useless.


=== Converting to HV ===
=== Converting to HV ===
In order to convert to HV, you must point the input cable (any "voltage") to the 3-dotted side and then link any number of output cables from the 1-dotted side. Remember to use input cables that can withstand the packets you are sending in and [[HV Cable]] or [[Glass Fibre Cable]] for the output.
In order to convert to HV, you must point the input cable to the 5-dotted side and then link any number of output cables from the 1-dotted sides.
 
=== Converting to EV ===
In order to convert to HV, you must '''apply redstone power through a lever, a repeater or a redstone wire''', point the input cables (any "voltage") to any 1-dotted side and then link the output cable from the 3-dotted side. Remember to use input cables that can withstand the packets you are sending in and [[HV Cable]] for the output.


== Latest Recipe ==
== Latest Recipe ==


{{Grid/Crafting Table
{{Grid/Crafting Table
|B1=4xIns. HV Cable
|B1=Insulated Gold Cable
|A2=Electronic Circuit|B2=MV Transformer|C2=Energy Crystal
|A2=Electronic Circuit|B2=MV Transformer|C2=Advanced RE-Battery
|B3=4xIns. HV Cable
|B3=Insulated Gold Cable
|Output=HV Transformer
|Output=HV Transformer
}}
}}


{{Energy
{{Energy
|Input= 2048 '''EU'''
|Input= 2048 EU/t
|Output= Variable
|Output= Variable
* Up to 2048 EU in 512 EU/p when redstone is '''not''' applied.
* In step-up mode, 2048 EU/t.
* 1 packet of 2048 EU/p when redstone is applied.
* In step-down mode, 512 EU/t.
|Storage=2048}}
|Storage=2048}}


Line 59: Line 56:
|-
|-
|}
|}
== Other usages ==
Multiple HVT may be directly installed on a [[Nuclear Reactor]] if the reactor outputs more than 2048 EU/t as conventional wires ([[HV cables]]) cannot handle packet sizes over 2048 EU/p.


{{Navigation}}
{{Navigation}}


[[Category:Wiring]]
[[Category:Wiring]]

Revision as of 23:21, 3 November 2013

HV Transformer
HV Transformer ig.png
Grid HV Transformer.png
Properties
Type Transformer
Tool Grid Wrench.png




Stackable Yes (64)





Energy Consumption
Max EU Input 2147483647 EU/t (??)
Technical Details
UU Cost {{{uu_cost}}}
First appearance ?
ID IC2:{{{id}}}


A HV Transformer is used to limit energy flow to 512 EU/t.

Transformers have two modes - step-up and step-down. By default, a transformer will operate in step-down mode unless it receives a redstone signal. This can be changed in the GUI.

In step-down mode, an HV transformer will accept up to 2048 EU/t to the 5-dot face without exploding, and output 512 EU/t from the 1-dot faces. Step-up mode appears to be useless.

Converting to HV[edit]

In order to convert to HV, you must point the input cable to the 5-dotted side and then link any number of output cables from the 1-dotted sides.

Latest Recipe[edit]


Grid Electronic Circuit.png


Grid Insulated Gold Cable.png
Grid MV Transformer.png
Grid Insulated Gold Cable.png


Grid Advanced RE-Battery.png


Grid HV Transformer.png


Energy[edit]

EU
Input 2048 EU/t
Output Variable
  • In step-up mode, 2048 EU/t.
  • In step-down mode, 512 EU/t.
Storage 2048

History (IC²)[edit]

IC² Minecraft Change
Industrial Craft²
1.97 1.2.5 Before this version of IC², the HV Transformer was crafted using this recipe:


Grid Electronic Circuit.png


Grid Insulated Copper Cable.png
Grid MV Transformer.png
Grid Insulated Copper Cable.png


Grid Energy Crystal.png


Grid HV Transformer.png





Retrieved from "https://wiki.industrial-craft.net/index.php?title=HV_Transformer&oldid=13116"