The Teleporter is a block that teleports the player standing directly above it to another linked teleporter.
The amount of EU it consumes depends on the distance and the amount of items in the player's inventory.
1. Place the Teleporter directly adjacent to a power storage unit such as an MFS Unit, or even a couple.
2. Use a FreqTrans to link one Teleporter to another.
3. Wire Redstone to the Teleporter.
4. Activate the Redstone.
If you have enough power in contiguous storage units, the power will be drained and you will be instantly teleported to the connected Teleporter.
Linking Teleporters is as easy as 1,2,3
- while holding a FreqTrans right-click on the first Teleporter.
- repeat for the second Teleporter.
- GO TELEPORTING. HAYO!
The power used by the Teleporter depends on a combination of what is being teleported and how far.
Teleporter EU cost Calculator
You can download a program to calculate EU cost of your teleporter(Programmed by Nexus/French) : v1.1.
You can also use the website at 
Formulas and Values
Animal weight: 100
Mob weight: 500
Player weight: 1000 + (100 per worn armor piece) + (100 per full item stack)
- Worst case player weight: 1000 + 4 * 100 + 4 * 9 * 100 = 5000
Energy cost: Floor(5 * Floor(Weight) * (Floor(Distance) + 10)^0.7)
- Minimum distance, worst case weight, 5 fully charged MFSU: ~51960
Energy Cost Example
Teleporting a player with only chest armor, boots, 64 cobblestone, 20 dirt, and 10 eggs for 15 distance.
Base cost: 1000
Armor cost: Chest(100) + Boots(100)
Inventory cost: Cobblestone(100 * 64/64) + Dirt(100 * 20/64) + Eggs(100 * 10/16) = 193.75
Player weight: 1000 + 200 + 193.75 = 1393.75
Total: Floor(5 * Floor(1393.75) * (15 + 10)^0.7) = 66294 EU
As you can see, the power requirements easily exceed even HV Cable, which is why a cable connection is insufficient. Although, an HV Cable might be sufficient for teleporting animals short distances (untested).
Distances are calculated in Euclidean meters.
Distance = sqrt( (dx)^2 + (dy)^2 + (dz)^2 )
dx, dy, and dz are distances in the x, y, and z directions, respectively.
If you place a teleporter at (10,50,-20) and another at (30,15,-60)
dx = 30-10 = 20
dy = 15-50 = -35
dz = (-60)-(-20) = -40
Distance = sqrt ( 20^2 + (-35)^2 + (-40)^2 ) = 56.78908
Energy Storage Devices
Energy will be drained from adjacent energy storage devices simultaneously. Equal amounts of energy will be drained from adjacent devices if there are enough energy. If three energy devices are adjacent 33.33% of the energy will be drained from each.
All types of energy storage can be used BatBox, MFE and MFSU.
Teleporters can explode if you leave and reload a world without quitting Minecraft.
Other mods like TMI (Too Many Items) can interfere with IC2. Specifically Frequency Transmitters when setting up Teleporters. This bug often makes Frequency Transmitters get stuck on the first Teleporter when linking two Teleporters. Afterwards it is not possible to unlink from the first Teleporter and all other connections made will link to the first Teleporter.
Teleporters can teleport players that are standing one block above the teleporter. This makes it possible to place a storage device on all 6 sides. It also makes it possible to camouflage teleporters under the ground. With IC2 1.81 you get stuck, the teleporter must be visible if you will arrive without damage.
In SMP there may be a Loop Bug  the solution is an Pulse Former from RedPower2 or without RP2 an pulse limiter redstone circuit. You could also neglect to put a power storage device under one of the teleporters, though it will be only a one way teleport system.
Teleporters can have one-way connections, which can give teleporter networks increased flexibility. Setting up a one-way connection requires at least three teleporters, referred to as A, B, and C. Link teleporter A to B and then C to B and the result will be a bi-directional link between B and C and a one-way link from A to B.
Say you have a "teleportation hub" where you have a series of outgoing teleporters and a central receiving pad for incoming teleportations. The outgoing teleporter (A) connects to a far-away destination. At the destination, another teleporter (B) receives teleportations from A but also allows travel back to the hub. However, instead of teleporting back to A when activating B, you arrive back at a central receiving teleporter (C, unpowered). To achieve this, first use an unlinked Frequency Transmitter on A, then use the same transmitter on B. Next, clear the transmitter by right-clicking any non-teleporter block. Then use the transmitter on C and finally on B again. The result is a network of A -> B -> C.
|1.97|| Before this version, the recipe of the Teleporter was this: |