Difference between revisions of "Overclocker upgrade"

From Industrial-Craft-Wiki
Jump to navigation Jump to search
m (→‎In Practice: Not sure what that bullet and semicolon were for. Deleted.)
(updated crafting table)
(21 intermediate revisions by 14 users not shown)
Line 1: Line 1:
[[Image:upgradedmachine.png|right]]
{{Experimental}}
Revised 2012-02-28 by Xenoflot for 1.71 power consumption


An [[overclocker upgrade]] can be used to speed up machines at the cost of higher energy consumption. Place one or more [[overclocker upgrade]]s into the four right-most slots to upgrade a machine.
{{Infobox
|type=Upgrade
|eu_use=160%
|optime=70%
|id=upgrade@0
}}


Each upgrade reduces the operating time to 70% of the previous value and increases energy consumption by 60%. The [[overclocker upgrade]]'s effects stack exponentially. For example, two upgrades makes the machine operate at (0.7)^2 = 0.49 times normal time (100% faster) and use 1.6^2 = 2.56 times the energy (139% more). 8 of them will run the machine at over 8 times normal speed, and use over 43 times as much EU.
'''Overclocker Upgrades''' are used to increase a machines operating speed at the cost of higher power demand and energy consumption. Overclocker Upgrades are placed in one of the four right-most upgrade slots in a machine's interface.


[[Overclocker upgrade]]s result in poorer energy efficiency (more EU will be consumed per operation). This results in a 12 percent increase in energy per operation per upgrade (0.7*1.6 = 1.12, (1.12)^10 = 3.11 ). While building multiple machines makes better use of a limited energy supply, but overclocking allows for reduced space and wiring requirements when time or compact construction are more important or energy is plentiful. The reduced efficiency can be mitigated by combining both approaches, dividing a number of [[overclocker upgrade]]s evenly between a handful of machines.
== Recipe ==
 
{{Grid/Crafting Table
An overclocked machine's speed cannot exceed 1 operation per tick, so adding additional [[overclocker upgrade]]s beyond that point is useless.
|A1=Cooling Cell|B1=Cooling Cell|C1=Cooling Cell
|A2=Insulated Copper Cable|B2=Electronic Circuit|C2=Insulated Copper Cable
|A3=|B3=|C3=
|Output=Overclocker upgrade|OA=2|nobreak=y
}}


== In Practice ==
[[Image:upgradedmachine.png|thumb|A {{Gin|Macerator}} with an '''Overclocker Upgrade''', two {{Gin|Transformer Upgrade}}s, and an {{Gin|Energy Storage Upgrade}}]]
Revised: 2012-02-28 by Xenoflot - Please advise me on IC2 forum of any mistakes.


'''tl;dr''' - Max speed benefits are obtained with: 16 [[overclocker upgrade]]s for [[Macerator]]s and [[Extractor]]s, 13 for [[Electro Furnace]]s and 10 for [[Recycler]]s;. In each case you're going to need to put in transformer upgrades, use glass cables and storage upgrades.
== Usage ==
Each Overclocker Upgrade '''reduces the operating time to 70% of the previous time''' but '''requires 60% more power'''. These effects stack exponentially. For example, with a machine with 2 Overclocker Upgrades each operation lasts <code>0.7<sup>2</sup> = 49%</code> the original time (204% original speed) and requires <code>1.6<sup>2</sup> = 256%</code> the original power. Using 8 Overclocker Upgrades will run the machine at over 17 times normal speed and requires 43 times the energy.


---
Overclocker Upgrades decrease a machine's energy efficiency, increasing EU use per operation. This is roughly a 12% increase in energy per operation per upgrade:


This section is intended to provide some explanation and practical examples for using [[overclocker upgrade]]s.<br />This revision includes the revised power consumption for 1.71.
<code>0.7*1.6 = 112%<br />
1.12<sup>8</sup> = 248% times the EU</code>


Each IndustrialCraft2 machine has a rated current draw (required EU/tick), a time to process the materials and internal EU storage. When calculating the effects of overclocking, we need to include these factors. The differences on each machine mean that some machines need more or less [[overclocker upgrade]]s to reach peak speed.
While building multiple machines makes better use of a limited energy supply, over-clocking allows for reduced space and wiring requirements when time or compact construction are more important or energy is plentiful. The reduced efficiency can be mitigated by combining both approaches: dividing a number of Overclocker Upgrades evenly between multiple machines.


The main limit to the number of overclockers you can use is the power requirement. To make machines run really fast, you need to feed them with multiple power supplies, big ones.<br />Also, you can't get it to process any faster than 1 operation per tick. Since there are only 20 ticks in a real-world second, you can never make an IC2 standard machine process more than 20 items per second.
An over-clocked machine's speed is limited by its inventory -- typically one stack of items, thus allowing up to 64 operations per tick. However, this would require too many Overclocker Upgrades to be practical.




'''Examples:'''
== In Practice ==
This section is intended to provide some explanation and practical examples for using Overclocker Upgrades.


A standard [[Macerator]] draws 2 EU/t, takes 20 seconds per grind and stores 625 EU.
This revision includes the revised power consumption for 1.71.


Five [[overclocker upgrade]]s are a great start. With 5 [[overclocker upgrade]]s, your [[Macerator]] draws 21 EU/t (which can be supplied by a single [[BatBox]]) and completes each grind in 3.5 seconds instead of 20!
Each IndustrialCraft<sup>2</sup> machine has a rated current draw (required EU/t), a time to process the materials and internal EU storage. When calculating the effects of over-clocking, we need to include these factors. The differences on each machine mean that some machines need more or less Overclocker Upgrades to reach peak speed.


With 8 [[overclocker upgrade]]s, your [[Macerator]] draws 85.9 EU/t and completes each grind in almost a second. You can still run this with copper cable but you'll need three [[BatBox]]es in parallel to supply the power. Alternatively, you can put in one [[Transformer upgrade]] (which allows 128 EU/t) and use an [[MFE Unit]] to power. Use [[Gold Cable]] or better!
The main limit to the number of Overclocker Upgrades you can use is the power requirement. To make machines run really fast, you need to feed them with multiple power supplies, big ones.


As you put in more [[overclocker upgrade]]s, the power requirements keep going up. 11 [[overclocker upgrade]]s want 352 EU/s which would require 11 [[BatBox]]es or 3 [[MFE Unit]]s to drive. My suggestion is you put 2 [[Transformer upgrade]]s in each machine early and then you can just upgrade to MFEs and MFSUs any time you're ready.  
=== Summary ===
Max speed benefits are obtained with: 28 Overclocker Upgrades for [[Macerator]]s and [[Extractor]]s, 25 for [[Electric Furnace]]s and 23 for [[Recycler]]s;. In each case you're going to need to put in transformer upgrades, use [[Glass Fibre Cable]] and storage upgrades.


There is a break-point when you reach 13 OC's on the Macerator, 10 on the Furnace and Extractor and 9 on the Recycler. The energy required per tick exceeds the machine's internal storage. As you approach this limit, you may see the machine flicker or stutter as if your batbox was running empty. If you put in one more overclocker, the machine will stop entirely. Now you need to add one or more [[Energy storage upgrade]]s before the machine will continue to function.
=== Examples ===
A standard [[Macerator]] draws 2 EU/t, takes 15 seconds per grind and stores 1,200 EU.


Maximum speed benefits can be achieved with 16 [[overclocker upgrade]]s in [[Macerator]]s and [[Extractor]]s, 13 in [[Electro Furnace]]s and 10 in [[Recycler]]s. In each case you're going to need to put in transformer upgrades, storage upgrades and use glass cables. The Macerator is the greediest and will need 8 [[MFS Unit]]s to supply the necessary power.
Five Overclocker Upgrades are a great start. With 5 Overclocker Upgrades,, your [[Macerator]] draws 21 EU/t (which can be supplied by a single [[BatBox]]) and completes each grind in 2.5 seconds instead of 15!


Credit: Sincere thanks to AkhkharuXul on the IC2 forum for providing reality checking on these numbers.
With 8 Overclocker Upgrades, your [[Macerator]] draws 85.9 EU/t and completes each operation in 0.9 seconds, just under a second! You can still run this with tin cable but you'll need three [[BatBox]]es in parallel to supply the power. Alternatively, you can put in one {{Gin|Transformer upgrade}} (which allows 128 EU/t) and use a [[CESU]] to power. Use [[Copper Cable]] or better!


== Recipe ==
As you put in more Overclocker Upgrades, the power requirements keep going up. 11 Overclocker Upgrades require 352 EU/t which would require 11 [[BatBox]]es or 3 [[CESU]]s to drive. My suggestion is to put 3 [[Transformer upgrade]]s in each machine early, and then upgrade to [[MFE]]s and [[MFSU]]s any time you're ready.


{{Grid/Crafting Table
There is a break-point when you reach 13 Overclocker Upgrades in the Macerator, 10 on the Furnace and Extractor and 9 on the Recycler. The energy required per tick exceeds the machine's internal storage. As you approach this limit, you may see the machine flicker or stutter as if your BatBox was running empty. If you put in one more Overclocker Upgrade, the machine will stop entirely. Now you need to add one or more {{Gin|Energy storage upgrade}}s before the machine will continue to function.
|A1=Cooling Cell|B1=Cooling Cell|C1=Cooling Cell
|A2=Insulated Copper Cable|B2=Electronic Circuit|C2=Insulated Copper Cable
|A3=|B3=|C3=
|Output=Overclocker upgrade
}}


{{Navigation}}
Maximum speed benefits can be achieved with 28 Overclocker Upgrades in [[Macerator]]s and [[Extractor]]s, 25 in [[Electric Furnace]]s and 23 in [[Recycler]]s. In each case you're going to need to put in transformer upgrades, storage upgrades and use [[Glass Fibre Cable]]. The Macerator is the greediest and will need 761 [[MFSU]]s to supply the necessary power.


[[Category:Upgrades]]
[[Category:Upgrades]]

Revision as of 17:15, 13 April 2019

Experimental-Only Content: This information has been updated to the V2.X version of IC².
The most recent version of IC² is V2.8.<html>.
Overclocker upgrade
Picture na.png
Grid Overclocker upgrade.png
Properties
Type Upgrade




Stackable Yes (64)





Energy Consumption
EU Use 160% EU/t
Technical Details
Operation Length 70% Seconds
UU Cost {{{uu_cost}}}
First appearance ?
ID IC2:upgrade@0


Overclocker Upgrades are used to increase a machines operating speed at the cost of higher power demand and energy consumption. Overclocker Upgrades are placed in one of the four right-most upgrade slots in a machine's interface.

Recipe[edit]

Grid Cooling Cell.png
Grid Insulated Copper Cable.png


Grid Cooling Cell.png
Grid Electronic Circuit.png


Grid Cooling Cell.png
Grid Insulated Copper Cable.png


Grid Overclocker upgrade.png

Overclocker upgrade

Overclocker upgrade

A Grid Macerator.png Macerator with an Overclocker Upgrade, two Grid Transformer Upgrade.png Transformer Upgrades, and an Grid Energy Storage Upgrade.png Energy Storage Upgrade

Usage[edit]

Each Overclocker Upgrade reduces the operating time to 70% of the previous time but requires 60% more power. These effects stack exponentially. For example, with a machine with 2 Overclocker Upgrades each operation lasts 0.72 = 49% the original time (204% original speed) and requires 1.62 = 256% the original power. Using 8 Overclocker Upgrades will run the machine at over 17 times normal speed and requires 43 times the energy.

Overclocker Upgrades decrease a machine's energy efficiency, increasing EU use per operation. This is roughly a 12% increase in energy per operation per upgrade:

0.7*1.6 = 112%
1.128 = 248% times the EU

While building multiple machines makes better use of a limited energy supply, over-clocking allows for reduced space and wiring requirements when time or compact construction are more important or energy is plentiful. The reduced efficiency can be mitigated by combining both approaches: dividing a number of Overclocker Upgrades evenly between multiple machines.

An over-clocked machine's speed is limited by its inventory -- typically one stack of items, thus allowing up to 64 operations per tick. However, this would require too many Overclocker Upgrades to be practical.


In Practice[edit]

This section is intended to provide some explanation and practical examples for using Overclocker Upgrades.

This revision includes the revised power consumption for 1.71.

Each IndustrialCraft2 machine has a rated current draw (required EU/t), a time to process the materials and internal EU storage. When calculating the effects of over-clocking, we need to include these factors. The differences on each machine mean that some machines need more or less Overclocker Upgrades to reach peak speed.

The main limit to the number of Overclocker Upgrades you can use is the power requirement. To make machines run really fast, you need to feed them with multiple power supplies, big ones.

Summary[edit]

Max speed benefits are obtained with: 28 Overclocker Upgrades for Macerators and Extractors, 25 for Electric Furnaces and 23 for Recyclers;. In each case you're going to need to put in transformer upgrades, use Glass Fibre Cable and storage upgrades.

Examples[edit]

A standard Macerator draws 2 EU/t, takes 15 seconds per grind and stores 1,200 EU.

Five Overclocker Upgrades are a great start. With 5 Overclocker Upgrades,, your Macerator draws 21 EU/t (which can be supplied by a single BatBox) and completes each grind in 2.5 seconds instead of 15!

With 8 Overclocker Upgrades, your Macerator draws 85.9 EU/t and completes each operation in 0.9 seconds, just under a second! You can still run this with tin cable but you'll need three BatBoxes in parallel to supply the power. Alternatively, you can put in one Grid Transformer upgrade.png Transformer upgrade (which allows 128 EU/t) and use a CESU to power. Use Copper Cable or better!

As you put in more Overclocker Upgrades, the power requirements keep going up. 11 Overclocker Upgrades require 352 EU/t which would require 11 BatBoxes or 3 CESUs to drive. My suggestion is to put 3 Transformer upgrades in each machine early, and then upgrade to MFEs and MFSUs any time you're ready.

There is a break-point when you reach 13 Overclocker Upgrades in the Macerator, 10 on the Furnace and Extractor and 9 on the Recycler. The energy required per tick exceeds the machine's internal storage. As you approach this limit, you may see the machine flicker or stutter as if your BatBox was running empty. If you put in one more Overclocker Upgrade, the machine will stop entirely. Now you need to add one or more Grid Energy storage upgrade.png Energy storage upgrades before the machine will continue to function.

Maximum speed benefits can be achieved with 28 Overclocker Upgrades in Macerators and Extractors, 25 in Electric Furnaces and 23 in Recyclers. In each case you're going to need to put in transformer upgrades, storage upgrades and use Glass Fibre Cable. The Macerator is the greediest and will need 761 MFSUs to supply the necessary power.