Industrial-Craft-Wiki - User contributions [en]

HV Transformer

2015-01-19T22:43:32Z

Fern Silverthorn:

{{Block
|type=Transformer
|gravity=No
|dirt=No
|transparent=No
|light=No
|tool=bwrench
|stackable=Yes (64)
|maxeu=2048
}}

Unlike Real Life™, there is no actual "voltage" in IC². EU travels in "packets" through wires with near-infinite speed and has smart pathfinding (somewhat like RP2 pneumatic tubes). Packets are measured in size (in EU/p) and volume (EU). (Size being the amount of energy it contains as it leaves a storage unit, volume being how much energy is left in each packet after inefficient cable usage).

Transformers have two modes - "step up" and "step down". By default, the transformer will be in step up mode when it receives a redstone signal, and step down mode otherwise. This can be changed in the GUI.

With default settings a HVT (or High Voltage Transformer) operates in two different ways.

* If redstone power is '''not''' applied, it consumes 2048 EU in '''any packet size''' and converts them into up to four 512 EU/p. '''All conversions are limited to one per tick. (Converting 2048 EU into 4x512 EU is considered one conversion.)'''
* If redstone power is applied, it consumes 2048 EU in '''any packet size''' and converts them into one 2048 EU/p. '''All conversions are limited to one per tick.'''
=== Converting to HV ===
In order to convert to HV, you must point the input cable (any "voltage") to the 3-dotted side and then link any number of output cables from the 1-dotted side. Remember to use input cables that can withstand the packets you are sending in and [[HV Cable]] or [[Glass Fibre Cable]] for the output.

=== Converting to EV ===
In order to convert to EV, you must '''apply redstone power through a lever, a repeater or a redstone wire''', point the input cables (any "voltage") to any 1-dotted side and then link the output cable from the 3-dotted side. Remember to use input cables that can withstand the packets you are sending in and [[HV Cable]] for the output.

== Recipe ==
{{Experimental}}
{{Grid/Crafting Table
|B1=2xIns. Gold Cable
|A2=Electronic Circuit|B2=MV Transformer|C2=Advanced RE-Battery
|B3=2xIns. Gold Cable
|Output=HV Transformer
}}

{{Energy
|Input= 2048 '''EU'''
|Output= Variable
* Up to 2048 EU in 512 EU/p when redstone is '''not''' applied.
* 1 packet of 2048 EU/p when redstone is applied.
|Storage=2048}}

== Usage ==
{{Grid/Crafting Table
|B1=4xIns. HV Cable
|A2=Advanced Circuit|B2=HV Transformer|C2=Energy Crystal
|B3=4xIns. HV Cable
|Output=EV Transformer
}}

== History (IC²) ==
{| class="wikitable"
|-
! IC²
! Minecraft
! Change
|-
| colspan=3 | Industrial Craft²
|-
! 2.0
| 1.6.4
| Before this version of IC², the [[HV Transformer]] was crafted using this recipe: <br/>
{{Grid/Crafting Table
|B1=4xIns. HV Cable
|A2=Electronic Circuit|B2=MV Transformer|C2=Energy Crystal
|B3=4xIns. HV Cable
|Output=HV Transformer
}}
|-
|}

== Other usages ==
Multiple HVT may be directly installed on a [[Nuclear Reactor]] if the reactor outputs more than 2048 EU/t as conventional wires ([[HV cables]]) cannot handle packet sizes over 2048 EU/p.

{{Navigation}}

[[Category:Wiring]]

MV Transformer

2015-01-19T22:41:47Z

Fern Silverthorn:

{{Block
|image=
|type=Wiring
|gravity=No
|dirt=No
|transparent=No
|light=no
|tool=bwrench
|stackable=Yes (64)
}}

{{IC²}}

The MV Transformer is used to turn '''High Power''' (512 [[EU#EU-Packet|EUP]]) into '''Medium Power''' (128 EUP) and back. This is useful for powering advanced machines and for medium-range energy transport.

By default, the Transformer accepts 512 [[EU#EU-Packet|EUP]] input and outputs 128 EUP. A 512 EUP or higher rated [[cable]] must be wired into the input face (the 3-dotted one) and 128 EUP or higher rated cable must be wired into the other faces.

Transformers have two modes - "step up" and "step down". By default, the transformer will be in step up mode when it receives a redstone signal, and step down mode otherwise. This can be changed in the GUI.

With default settings a Redstone signal may be applied to reverse the conversion, thereby emitting 512 [[EU#EU-Packet|EUP]] from the output face (the 3-dotted one), and accepting 128 EUP or lower from the input faces. In reverse operation, 512 EUP or higher rated [[cable]] must be wired to the output face and any rate cable may be wired to the input faces.

It can handle a maximum of one conversion per tick, limiting the maximum transfer to 512 [[EU#EU/t|EU/t]] in either mode.

== Recipe ==
{{Experimental}}
{{Grid/Crafting Table
|A1=|B1=Insulated Copper Cable|C1=
|A2=|B2=Machine|C2=
|A3=|B3=Insulated Copper Cable|C3=
|Output=MV Transformer
}}

== Usage ==

When using any Transformer, remember that the 3-dotted side means '''higher current''' and the 1-dotted sides mean '''lower current'''. You can change the direction the 3-dotted side is facing by right-clicking a 1-dotted face with a [[Wrench]].

=== Converting to MV: ===

In order to convert from HV to MV, you must point the [[Cable|cable]] carrying HV from a [[HV Transformer]] or [[MFS Unit]] to the 3-dotted side and then link a cable that can carry MV to one of the sides with a single dot. Then that cable will be carrying MV that you can link to advanced machines, store in a [[MFE Transmitter]] or convert to LV with an [[LV Transformer]].

=== Converting to HV: ===

In order to convert from MV to HV, point the cable carrying MV from a [[MFE Transmitter]] or a [[LV Transformer]] to one of the one-dotted sides and then link a cable that can carry HV to the 3-dotted side. '''Do not forget to apply redstone''' to the MV Transformer.

{{Energy|Input=128 or 512|Output=128 or 512|Storage=-}}

{{Navigation}}

HV Transformer

2015-01-19T22:39:11Z

Fern Silverthorn:

{{Block
|type=Transformer
|gravity=No
|dirt=No
|transparent=No
|light=No
|tool=bwrench
|stackable=Yes (64)
|maxeu=2048
}}

Unlike Real Life™, there is no actual "voltage" in IC². EU travels in "packets" through wires with near-infinite speed and has smart pathfinding (somewhat like RP2 pneumatic tubes). Packets are measured in size (in EU/p) and volume (EU). (Size being the amount of energy it contains as it leaves a storage unit, volume being how much energy is left in each packet after inefficient cable usage).

A HVT (or High Voltage Transformer) operates in two different ways.

* If redstone power is '''not''' applied, it consumes 2048 EU in '''any packet size''' and converts them into up to four 512 EU/p. '''All conversions are limited to one per tick. (Converting 2048 EU into 4x512 EU is considered one conversion.)'''
* If redstone power is applied, it consumes 2048 EU in '''any packet size''' and converts them into one 2048 EU/p. '''All conversions are limited to one per tick.'''
=== Converting to HV ===
In order to convert to HV, you must point the input cable (any "voltage") to the 3-dotted side and then link any number of output cables from the 1-dotted side. Remember to use input cables that can withstand the packets you are sending in and [[HV Cable]] or [[Glass Fibre Cable]] for the output.

=== Converting to EV ===
In order to convert to EV, you must '''apply redstone power through a lever, a repeater or a redstone wire''', point the input cables (any "voltage") to any 1-dotted side and then link the output cable from the 3-dotted side. Remember to use input cables that can withstand the packets you are sending in and [[HV Cable]] for the output.

== Recipe ==
{{Experimental}}
Behavior may also be controlled with the transformer GUI, modes include: Fixed up/down and redstone controlled.

{{Grid/Crafting Table
|B1=2xIns. Gold Cable
|A2=Electronic Circuit|B2=MV Transformer|C2=Advanced RE-Battery
|B3=2xIns. Gold Cable
|Output=HV Transformer
}}

{{Energy
|Input= 2048 '''EU'''
|Output= Variable
* Up to 2048 EU in 512 EU/p when redstone is '''not''' applied.
* 1 packet of 2048 EU/p when redstone is applied.
|Storage=2048}}

== Usage ==
{{Grid/Crafting Table
|B1=4xIns. HV Cable
|A2=Advanced Circuit|B2=HV Transformer|C2=Energy Crystal
|B3=4xIns. HV Cable
|Output=EV Transformer
}}

== History (IC²) ==
{| class="wikitable"
|-
! IC²
! Minecraft
! Change
|-
| colspan=3 | Industrial Craft²
|-
! 2.0
| 1.6.4
| Before this version of IC², the [[HV Transformer]] was crafted using this recipe: <br/>
{{Grid/Crafting Table
|B1=4xIns. HV Cable
|A2=Electronic Circuit|B2=MV Transformer|C2=Energy Crystal
|B3=4xIns. HV Cable
|Output=HV Transformer
}}
|-
|}

== Other usages ==
Multiple HVT may be directly installed on a [[Nuclear Reactor]] if the reactor outputs more than 2048 EU/t as conventional wires ([[HV cables]]) cannot handle packet sizes over 2048 EU/p.

{{Navigation}}

[[Category:Wiring]]

MV Transformer

2015-01-19T22:38:47Z

Fern Silverthorn:

{{Block
|image=
|type=Wiring
|gravity=No
|dirt=No
|transparent=No
|light=no
|tool=bwrench
|stackable=Yes (64)
}}

{{IC²}}

The MV Transformer is used to turn '''High Power''' (512 [[EU#EU-Packet|EUP]]) into '''Medium Power''' (128 EUP) and back. This is useful for powering advanced machines and for medium-range energy transport.

By default, the Transformer accepts 512 [[EU#EU-Packet|EUP]] input and outputs 128 EUP. A 512 EUP or higher rated [[cable]] must be wired into the input face (the 3-dotted one) and 128 EUP or higher rated cable must be wired into the other faces.

A Redstone signal may be applied to reverse the conversion, thereby emitting 512 [[EU#EU-Packet|EUP]] from the output face (the 3-dotted one), and accepting 128 EUP or lower from the input faces. In reverse operation, 512 EUP or higher rated [[cable]] must be wired to the output face and any rate cable may be wired to the input faces.

It can handle a maximum of one conversion per tick, limiting the maximum transfer to 512 [[EU#EU/t|EU/t]] in either mode.

== Recipe ==
{{Experimental}}
Behavior may also be controlled with the transformer GUI, modes include: Fixed up/down and redstone controlled.

{{Grid/Crafting Table
|A1=|B1=Insulated Copper Cable|C1=
|A2=|B2=Machine|C2=
|A3=|B3=Insulated Copper Cable|C3=
|Output=MV Transformer
}}

== Usage ==

When using any Transformer, remember that the 3-dotted side means '''higher current''' and the 1-dotted sides mean '''lower current'''. You can change the direction the 3-dotted side is facing by right-clicking a 1-dotted face with a [[Wrench]].

=== Converting to MV: ===

In order to convert from HV to MV, you must point the [[Cable|cable]] carrying HV from a [[HV Transformer]] or [[MFS Unit]] to the 3-dotted side and then link a cable that can carry MV to one of the sides with a single dot. Then that cable will be carrying MV that you can link to advanced machines, store in a [[MFE Transmitter]] or convert to LV with an [[LV Transformer]].

=== Converting to HV: ===

In order to convert from MV to HV, point the cable carrying MV from a [[MFE Transmitter]] or a [[LV Transformer]] to one of the one-dotted sides and then link a cable that can carry HV to the 3-dotted side. '''Do not forget to apply redstone''' to the MV Transformer.

{{Energy|Input=128 or 512|Output=128 or 512|Storage=-}}

{{Navigation}}

HV Cable

2015-01-19T01:09:08Z

Fern Silverthorn:

HV cables are the 4th tier of [[Cable|cables]]. They can tolerate '''High Voltage''' (512 [[EU|EU/t]]) and '''Extreme Voltage''' (2048 EU/t).

== Recipe ==
{{Experimental}}
{|
|{{Grid/MetalFormer
|Mode=Extruding
|Top=Iron
|Bottom=RE Battery (Charged)
|Output=HV Cable|OA=4
}}
|{{Grid/Crafting Table
|A1=Rubber|B1=Rubber|C1=Rubber
|A2=HV Cable
|Output=3xIns. HV Cable
|Output-link=3xIns. HV Cable
}}
{{Grid/Crafting Table
|A1=Cutter|B1=Iron Plate
|Output=HV Cable
|OA=4
}}
|}

{{Classic}}
HV-Cables have an extremely high distance-related energy loss. They can have 3 different levels of insulation. Considering that a shock from a poorly insulated HV cable will most likely prove fatal, it is recommended to insulate them well unless the cable is located in a completely unreachable area. Even then, insulation should be applied to reduce the massive energy losses.
{|
|{{Grid/Crafting Table
|A2=Refined Iron|B2=Refined Iron|C2=Refined Iron
|Output=HV Cable|OA=12
}}
|{{Grid/Crafting Table
|B1=Rubber
|A2=Rubber|B2=Refined Iron|C2=Rubber
|B3=Rubber
|Output=Insulated HV Cable|OA=4
}}
|}
{|
|{{Grid/Crafting Table
|A1=Rubber|B1=HV Cable
|Output=Insulated HV Cable
}}
|{{Grid/Crafting Table
|A1=Rubber|B1=Insulated HV Cable
|Output=2xIns. HV Cable
}}
|}
{|
|{{Grid/Crafting Table
|A1=Rubber|B1=Rubber|C1=HV Cable
|Output=2xIns. HV Cable
}}
|{{Grid/Crafting Table
|A1=Rubber|B1=Rubber|C1=Insulated HV Cable
|Output=3xIns. HV Cable
|Output-link=3xIns. HV Cable
}}
|}
{|
|{{Grid/Crafting Table
|A1=Rubber|B1=Rubber|C1=Rubber
|A2=HV Cable
|Output=3xIns. HV Cable
|Output-link=3xIns. HV Cable
}}
|{{Grid/Crafting Table
|A1=Rubber|B1=2xIns. HV Cable
|Output=3xIns. HV Cable
|Output-link=3xIns. HV Cable
}}
|}

=== [[Cable#Cable Efficiency|Cable Efficiency]] ===

{| class="wikitable"
!Cable type
!EU/b
!Energy loss
|-
|HV Uninsulated
|1
|1 EU every block
|-
|HV Insulated
|0.95
|1 EU every 1.05 blocks
|-
|HV 2x Insulated
|0.9
|1 EU every 1.11 blocks
|-
|HV 3x Insulated
|0.8
|1 EU every 1.25 blocks
|}

{{Navigation}}

[[Category:Wiring]]

HV Cable

2015-01-19T01:08:49Z

Fern Silverthorn:

HV cables are the 4 tier of [[Cable|cables]]. They can tolerate '''High Voltage''' (512 [[EU|EU/t]]) and '''Extreme Voltage''' (2048 EU/t).

== Recipe ==
{{Experimental}}
{|
|{{Grid/MetalFormer
|Mode=Extruding
|Top=Iron
|Bottom=RE Battery (Charged)
|Output=HV Cable|OA=4
}}
|{{Grid/Crafting Table
|A1=Rubber|B1=Rubber|C1=Rubber
|A2=HV Cable
|Output=3xIns. HV Cable
|Output-link=3xIns. HV Cable
}}
{{Grid/Crafting Table
|A1=Cutter|B1=Iron Plate
|Output=HV Cable
|OA=4
}}
|}

{{Classic}}
HV-Cables have an extremely high distance-related energy loss. They can have 3 different levels of insulation. Considering that a shock from a poorly insulated HV cable will most likely prove fatal, it is recommended to insulate them well unless the cable is located in a completely unreachable area. Even then, insulation should be applied to reduce the massive energy losses.
{|
|{{Grid/Crafting Table
|A2=Refined Iron|B2=Refined Iron|C2=Refined Iron
|Output=HV Cable|OA=12
}}
|{{Grid/Crafting Table
|B1=Rubber
|A2=Rubber|B2=Refined Iron|C2=Rubber
|B3=Rubber
|Output=Insulated HV Cable|OA=4
}}
|}
{|
|{{Grid/Crafting Table
|A1=Rubber|B1=HV Cable
|Output=Insulated HV Cable
}}
|{{Grid/Crafting Table
|A1=Rubber|B1=Insulated HV Cable
|Output=2xIns. HV Cable
}}
|}
{|
|{{Grid/Crafting Table
|A1=Rubber|B1=Rubber|C1=HV Cable
|Output=2xIns. HV Cable
}}
|{{Grid/Crafting Table
|A1=Rubber|B1=Rubber|C1=Insulated HV Cable
|Output=3xIns. HV Cable
|Output-link=3xIns. HV Cable
}}
|}
{|
|{{Grid/Crafting Table
|A1=Rubber|B1=Rubber|C1=Rubber
|A2=HV Cable
|Output=3xIns. HV Cable
|Output-link=3xIns. HV Cable
}}
|{{Grid/Crafting Table
|A1=Rubber|B1=2xIns. HV Cable
|Output=3xIns. HV Cable
|Output-link=3xIns. HV Cable
}}
|}

=== [[Cable#Cable Efficiency|Cable Efficiency]] ===

{| class="wikitable"
!Cable type
!EU/b
!Energy loss
|-
|HV Uninsulated
|1
|1 EU every block
|-
|HV Insulated
|0.95
|1 EU every 1.05 blocks
|-
|HV 2x Insulated
|0.9
|1 EU every 1.11 blocks
|-
|HV 3x Insulated
|0.8
|1 EU every 1.25 blocks
|}

{{Navigation}}

[[Category:Wiring]]

HV Transformer

2015-01-19T01:03:33Z

Fern Silverthorn:

{{Block
|type=Transformer
|gravity=No
|dirt=No
|transparent=No
|light=No
|tool=bwrench
|stackable=Yes (64)
|maxeu=2048
}}

Unlike Real Life™, there is no actual "voltage" in IC². EU travels in "packets" through wires with near-infinite speed and has smart pathfinding (somewhat like RP2 pneumatic tubes). Packets are measured in size (in EU/p) and volume (EU). (Size being the amount of energy it contains as it leaves a storage unit, volume being how much energy is left in each packet after inefficient cable usage).

A HVT (or High Voltage Transformer) operates in two different ways.

* If redstone power is '''not''' applied, it consumes 2048 EU in '''any packet size''' and converts them into up to four 512 EU/p. '''All conversions are limited to one per tick. (Converting 2048 EU into 4x512 EU is considered one conversion.)'''
* If redstone power is applied, it consumes 2048 EU in '''any packet size''' and converts them into one 2048 EU/p. '''All conversions are limited to one per tick.'''
=== Converting to HV ===
In order to convert to HV, you must point the input cable (any "voltage") to the 3-dotted side and then link any number of output cables from the 1-dotted side. Remember to use input cables that can withstand the packets you are sending in and [[HV Cable]] or [[Glass Fibre Cable]] for the output.

=== Converting to EV ===
In order to convert to EV, you must '''apply redstone power through a lever, a repeater or a redstone wire''', point the input cables (any "voltage") to any 1-dotted side and then link the output cable from the 3-dotted side. Remember to use input cables that can withstand the packets you are sending in and [[HV Cable]] for the output.

== Recipe ==
{{Experimental}}
* In the Experimental version conversion direction and redstone behavior may also be controlled with the transformer GUI.
* Modes include: Fixed up/down and redstone controlled.

{{Grid/Crafting Table
|B1=2xIns. Gold Cable
|A2=Electronic Circuit|B2=MV Transformer|C2=Advanced RE-Battery
|B3=2xIns. Gold Cable
|Output=HV Transformer
}}

{{Energy
|Input= 2048 '''EU'''
|Output= Variable
* Up to 2048 EU in 512 EU/p when redstone is '''not''' applied.
* 1 packet of 2048 EU/p when redstone is applied.
|Storage=2048}}

== Usage ==
{{Grid/Crafting Table
|B1=4xIns. HV Cable
|A2=Advanced Circuit|B2=HV Transformer|C2=Energy Crystal
|B3=4xIns. HV Cable
|Output=EV Transformer
}}

== History (IC²) ==
{| class="wikitable"
|-
! IC²
! Minecraft
! Change
|-
| colspan=3 | Industrial Craft²
|-
! 2.0
| 1.6.4
| Before this version of IC², the [[HV Transformer]] was crafted using this recipe: <br/>
{{Grid/Crafting Table
|B1=4xIns. HV Cable
|A2=Electronic Circuit|B2=MV Transformer|C2=Energy Crystal
|B3=4xIns. HV Cable
|Output=HV Transformer
}}
|-
|}

== Other usages ==
Multiple HVT may be directly installed on a [[Nuclear Reactor]] if the reactor outputs more than 2048 EU/t as conventional wires ([[HV cables]]) cannot handle packet sizes over 2048 EU/p.

{{Navigation}}

[[Category:Wiring]]

HV Transformer

2015-01-19T01:02:09Z

Fern Silverthorn: Added experimental information.

{{Block
|type=Transformer
|gravity=No
|dirt=No
|transparent=No
|light=No
|tool=bwrench
|stackable=Yes (64)
|maxeu=2048
}}

Unlike Real Life™, there is no actual "voltage" in IC². EU travels in "packets" through wires with near-infinite speed and has smart pathfinding (somewhat like RP2 pneumatic tubes). Packets are measured in size (in EU/p) and volume (EU). (Size being the amount of energy it contains as it leaves a storage unit, volume being how much energy is left in each packet after inefficient cable usage).

A HVT (or High Voltage Transformer) operates in two different ways.

* If redstone power is '''not''' applied, it consumes 2048 EU in '''any packet size''' and converts them into up to four 512 EU/p. '''All conversions are limited to one per tick. (Converting 2048 EU into 4x512 EU is considered one conversion.)'''
* If redstone power is applied, it consumes 2048 EU in '''any packet size''' and converts them into one 2048 EU/p. '''All conversions are limited to one per tick.'''
== ==
{{Experimental}}
* In the Experimental version conversion direction and redstone behavior may also be controlled with the transformer GUI.
* Modes include: Fixed up/down and redstone controlled.
=== Converting to HV ===
In order to convert to HV, you must point the input cable (any "voltage") to the 3-dotted side and then link any number of output cables from the 1-dotted side. Remember to use input cables that can withstand the packets you are sending in and [[HV Cable]] or [[Glass Fibre Cable]] for the output.

=== Converting to EV ===
In order to convert to EV, you must '''apply redstone power through a lever, a repeater or a redstone wire''', point the input cables (any "voltage") to any 1-dotted side and then link the output cable from the 3-dotted side. Remember to use input cables that can withstand the packets you are sending in and [[HV Cable]] for the output.

== Recipe ==
{{Experimental}}
{{Grid/Crafting Table
|B1=2xIns. Gold Cable
|A2=Electronic Circuit|B2=MV Transformer|C2=Advanced RE-Battery
|B3=2xIns. Gold Cable
|Output=HV Transformer
}}

{{Energy
|Input= 2048 '''EU'''
|Output= Variable
* Up to 2048 EU in 512 EU/p when redstone is '''not''' applied.
* 1 packet of 2048 EU/p when redstone is applied.
|Storage=2048}}

== Usage ==
{{Grid/Crafting Table
|B1=4xIns. HV Cable
|A2=Advanced Circuit|B2=HV Transformer|C2=Energy Crystal
|B3=4xIns. HV Cable
|Output=EV Transformer
}}

== History (IC²) ==
{| class="wikitable"
|-
! IC²
! Minecraft
! Change
|-
| colspan=3 | Industrial Craft²
|-
! 2.0
| 1.6.4
| Before this version of IC², the [[HV Transformer]] was crafted using this recipe: <br/>
{{Grid/Crafting Table
|B1=4xIns. HV Cable
|A2=Electronic Circuit|B2=MV Transformer|C2=Energy Crystal
|B3=4xIns. HV Cable
|Output=HV Transformer
}}
|-
|}

== Other usages ==
Multiple HVT may be directly installed on a [[Nuclear Reactor]] if the reactor outputs more than 2048 EU/t as conventional wires ([[HV cables]]) cannot handle packet sizes over 2048 EU/p.

{{Navigation}}

[[Category:Wiring]]

Copper Cable

2015-01-19T00:46:40Z

Fern Silverthorn:

Copper cables are Tier 2, the 2nd-most common cable tier. They are capable of handling '''Medium Voltage''' (up to 128 [[EU|EU-p]]), losing 1 EU every 5 blocks.

They are also used in the creation of [[Electronic Circuit|Electronic Circuits]].

== Crafting ==

{|
|{{Grid/Crafting Table
|A2=Copper Plate|B2=Cutter
|Output=Copper Cable|OA=2
|Output-link=Copper Cable
}}
|{{Grid/Crafting Table
|A1=Rubber|B1=Copper Cable
|Output=Insulated Copper Cable
|Output-link=Insulated Copper Cable
}}
|}

==Shocks==
(OLD)If you move too close to the uninsulated copper cable you may get an electric shock which does damage to the player so it's best to insulate your cables.
* This feature seems to be disabled in Experimental versions of IC2 (Test made in 2_2.0.277-experimental)

== [[Cable#Cable Efficiency|Cable Efficiency]] ==

{| class="wikitable"
!Cable type
!Max packet
|-
| align="left" | Uninsulated Copper Wire
| align="right" | 128 EU-p
|-
| align="left" | Insulated Copper Wire
| align="right" | 128 EU-p
|}

{{Navigation}}

[[Category:Wiring]]

Gold Cable

2015-01-19T00:45:30Z

Fern Silverthorn:

{{Experimental}}
Gold cables are Tier 3 [[Cable|cable]] type. They suffer higher distance-related energy losses than [[Copper Cable]]s, but are able to carry '''High Voltage''', up to 512 [[EU|EU-p]]. Gold cables have 2 different levels of insulation, with the 2x insulation providing smaller energy losses per tile and less shock damage from high voltage.

== Crafting ==

{|
|{{Grid/Crafting Table
|A1=Gold Plate|B1=Cutter
|Output=Gold Cable|OA=4
}}
|
|}
{|
|{{Grid/Crafting Table
|A1=Rubber|B1=Rubber
|A2=Gold Cable
|Output=2xIns. Gold Cable
}}
|}

== [[Cable#Cable Efficiency|Cable Efficiency]] ==

{| class="wikitable"
! Cable type
! Max packet
|-
| Uninsulated Gold Cable
| 512 EU-p
|-
| Insulated Gold Cable
| 512 EU-p
|}

{{Navigation}}

[[Category:Wiring]]

Gold Cable

2015-01-19T00:45:06Z

Fern Silverthorn: Fixed typo

{{Experimental}}
Gold cables are Tier 2 [[Cable|cable]] type. They suffer higher distance-related energy losses than [[Copper Cable]]s, but are able to carry '''High Voltage''', up to 512 [[EU|EU-p]]. Gold cables have 2 different levels of insulation, with the 2x insulation providing smaller energy losses per tile and less shock damage from high voltage.

== Crafting ==

{|
|{{Grid/Crafting Table
|A1=Gold Plate|B1=Cutter
|Output=Gold Cable|OA=4
}}
|
|}
{|
|{{Grid/Crafting Table
|A1=Rubber|B1=Rubber
|A2=Gold Cable
|Output=2xIns. Gold Cable
}}
|}

== [[Cable#Cable Efficiency|Cable Efficiency]] ==

{| class="wikitable"
! Cable type
! Max packet
|-
| Uninsulated Gold Cable
| 512 EU-p
|-
| Insulated Gold Cable
| 512 EU-p
|}

{{Navigation}}

[[Category:Wiring]]